After introducing a successful Lasagna 3Dfx Cooler for single graphics chipset, TennMax incorporates many years of thermal management experiences and technologies to create another best possible consolidated thermal solution for your VoodooČ board(s).  This special cooler will boost your power games, stabilize your graphic display, and prolong the life of your chipsets. This cooler is a must to aggressively overclock your graphics board.

It cools all three 3Dfx chips by contact! The Stealth V2 Cooler, which has all the key components thermally connected to the hot chips.  The Stealth V2 Cooler takes the thermal energy generated by all three 3Dfx graphics chipsets (2 TMUs and 1 FBI), conducts the heat through the "thermal transferring plate", and then moves the energy to the Lasagna cooler.   Lasagna, positioned in the middle of the thermal transferring plate, uses its multileaf plate design with an extra large surface area (for heat dissipation) and an embedded ball bearing fan , effectively removes all the thermal energy (heat) flown into the cooler.

Lasagna, an integrated low profile fan/sink cooler, is a patented technology owned by TennMax.   This unique cooler, by itself, can effectively cool a single microprocessor of 25 Watts of power.  The Lasagna Slim Cooler is an established product, and has been specified for use in many computer products as the solution to cool advanced CPUs (Pentium MMX, AMD K6-2, etc.). The low profile design is particularly useful for tight spaces or space constrained designs (click here to read more about the Lasagna Slim Cooler for single microprocessor).

• the heat is taken off the chipset by direct contact instead of blowing air on top of the board. (note: air is a very poor thermal conductor)

• the power consumption, noise level and price are reduced by having one Lasagna cooler taking care of the heat dissipation.

• the Stealth V2 Cooler fits perfectly on all VoodooČ cards made based on the reference board, including Creative Labs' 3D Blaster V2, Diamond's Monster II, Jazz Renegate3D, Orchid's Righteous II, Magic 3D2, Guillemot MaxGamer, Wicked 3D, Ambush 3D, and more...

The Stealth V2 Cooler
has many advantages over the competition

Stealth V2 Cooler integrated into & flying with
a 3Dfx Voodoo² reference board

Note: ObsidianX, and new 3Dfx Voodoo 1000 (origially, STB BlackMagic3D)
cards are different from this reference design custom design is required
Custom Stealth V2 Cooler is now available for Pure3D II Voodoo2 card, here are pictures.
Standard Stealth also fits Micro Conversions Game Wizard Voodoo2 Board for Mac!

The Stealth V2 Cooler is attached to the VoodooČ board using a very thin adhesive tape with high thermal conductivity, and bond strength, which conducts all the heat come out of the 3Dfx chipsets on VoodooČ boards into the special thermal transfer plate.

It is very easy to install the Stealth V2 Cooler, no tools needed. All you need is to clean the chipset surfaces (with common degrease solvent). Peel off three protective film on the tapes (release liners) in the back side of the Stealth V2 Cooler.  Place the exposed adhesive onto the 3Dfx chips, and press with finger pressure on the plate above the chips for more than 10 seconds to activate the bond strength between the plate and the chips. And you're now ready to FLY to a higher altitude with your Voodoo² accelerated graphics card ......

Once installed, the Stealth V2 Cooler becomes an integrated part of your Voodoo² board.  However, if necessary, the V2 Cooler can be readily separated from the chipset just by gently prying apart using a flat object such as a knife edge. Unlike other thermal solutions, the Stealth V2 Cooler does not void your VoodooČ's warranty as no modification is made to the card.

Two Voodoo2 in SLI? No problem at all!

notes:  For SLI two-card configuration, the height of the Stealth V2 Cooler is only 11 mm (0.433 inch) so it fits in between boards well.  Anders Hammervald has done his review in SLI.
         The cooler comes with standard 4-pin connector which can be easily connected to the power supplies or "looped (passed)" through other cords for CD-ROM, discket, or hard drives.