TennMax VIVA TF Coolers
for   Pentium® II processors & Athlon®

TennMax VIVA P2 Cooler for Pentium II Processor

***   TennMax VIVA P2 Cooler is engineered and optimized   ***
 based on state-of-the-art Computational Fluid Dynamics (CFD)Techniques

new:  Review on VIVA TF Cooler by OCTanePC (updated Jan. 1999)

Here is the VIVA P2 Cooler for Pentium II & Athlon ....

VIVA P2 Cooler for Pentium II

Comparison of Thermal Performance, Selected Pentium II Coolers

P2 Cooler  +
Thermal Interface		 T-case, oC T-ambient, oC Tc-Ta, oC Thermal
Resistance
VIVA + Grease 47.09 31.74 15.35 0.532 ºC/W
VIVA + PCM1 47.11 31.45 15.67 0.544 ºC/W
VIVA + PCM2 49.88 32.25 17.63 0.612 ºC/W
Fan/sink (1)+Grease 48.73 31.52 17.21 0.597 ºC/W
Fan/sink (2)+Grease 54.71 34.24 20.47 0.710 ºC/W
Fan/sink (3)+Grease 53.10 35.20 17.90 0.621 ºC/W
Heat sink only+Grease 59.95 35.18 24.77 0.860 ºC/W

* VIVA = TennMax VIVA P2 Cooler
* Grease = Thermal grease DC340
* PCM1 = Grease like phase change material
* PCM2 = Dry elastomeric phase change material (0.20 mm thick)
* Fan/sink (1) = fan on die cast heat sink, by "S" company
* Fan/sink (2) = fan/sink with clips by "T" company
* Fan/sink (3) = Special Fan/Sink with clips by "AS" company
* Heat sink only = Large Heat Sink (no fan) with clip by "W "company

All tests were run using a computer with Pentium II 266 MHz
processor  (running at approximate 78% of full 37 Watts power)

Simple Steps to Assemble VIVA on/off Pentium II and Athlon Cartridge

VIVA P2 Sketch

To Mount the VIVA on P-II

1. Push both "Levers" upward (toward the fan) to expose the "hooks" at the opposite ends of the clips.

2. Drop the "end hooks" into the holes B.

3. Pull the cooler slightly towards the top of the cartridge. This will position two cooler's bottom pins into the "locator holes" on the cartridge plate.

4. Firmly press down both levers into the holes A. You should hear a crispy click when the hook sets.

To Dismount the VIVA off P-II

1.Use a small screw driver and place it under the small "Notch Hooks" just below the Levers. Pry the notch upward towards the fan. You should hear a clear clicking sound when clip releases.

2. The VIVA cooler is then easily removed from the cartridge.

 

The VIVA Dimensions:

vv_dimen.gif (6874 bytes)

Here is a custom VIVA TF Cooler : with two ball bearing fans on top of the same VIVA heatsink. The wires are spliced, so only one 3-wire connector to the Pentium II/Athlon Motherboard.  This custom cooler is especially useful for P2 overclockers.

Custom VIVA TF P2 Cooler
new:  Read the review on VIVA TF Cooler by John Ariel

Check this our for the new Celeron TF Cooler for Celeron SLOT 1, and

MEGA7 Cooler for Celeron PPGA in Socket 370

e-mail TennMax@aol.com now

** We Promise to Respond Immediately **

VIVA K7 STF -  MEGA7/Ultra for Socket 7 - Lasagna for tight space
  [Cooler for Athlon]     [Cooler for S 7/370]     [ Cooler for SBC&3D cards ]

[New 440BX Chipset solution]

[TennMax Home Page][order information]